UM-OLSR is an implementation of the OLSR (Optimized Link State Routing) protocol for the ns-2 Network Simulator. The code is released under the terms of the GNU General Public License (GPL). Due to lack of time this project is not maintained by myself any more, feel free to take over the task of maintenance if you are interested.
UM-OLSR complies with IETF RFC 3626 and supports all core functionalities of OLSR plus the link-layer feedback option. The software has been successfully tested on ns-2, and patches for several versions of the simulator are provided. It is widely employed by the wireless communications research community, as the high number of references in research papers reveal. In addition, it was ported to ns-3 by Gustavo Carneiro (INESC Porto) and to Omnet++ by Alfonso Ariza (Universidad de Málaga). Thus, you can also run OLSR simulations in modern network simulators.
- Compliant with core OLSR (as described in RFC 3626).
- Support for link-layer feedback.
- Highly configurable from TCL scripts, i.e., without the need of recompiling the whole simulator. You can:
- Activate/deactivate debug mode.
- Change the interval at which every message type is sent.
- Change nodes’ willingness for forwarding data packets on behalf of other nodes.
- Print whatever data structure managed by a node at a certain time.
The source code of UM-OLSR in hosted on SourceForge.net: download.
Here you can find a sample script for configuring a simulation, as well as some UM-OLSR patches for different versions of ns-2 that were contributed by different people. Thanks a lot to all of them.
- um-olsr-2.33_v0.8.8.patch by Damian Philipp.
- um-olsr-2.34_v0.8.8.patch by Damian Philipp.
- um-olsr-2.35_v0.8.8.patch by Andrey Lyubimov.
I assume that you have downloaded and unpackaged the allinone distribution of ns-2 (any of the versions supported by UM-OLSR). Copy um-olsr-0.8.8.tgz (substitute “0.8.8″ for your UM-OLSR version number) into ns-allinone-2.29/ns-2.29/ (substitute “2.29″ for your ns-2 version number), and then do:
$ cd ns-allinone-2.29/ns-2.29/ $ tar zxvf um-olsr-0.8.8.tgz $ ln -s ./um-olsr-0.8.8 ./olsr $ patch -p1 < olsr/um-olsr_ns-2.29_v0.8.8.patch
If you had not installed ns-2 yet, then do the following:
$ cd .. $ ./install
On the other hand, if you are installing UM-OLSR on a running installation of ns-2:
$ ./configure $ make distclean $ ./configure $ make
Note that the code should work on most ns-2 releases, but only patches for some versions are provided. If you need UM-OLSR on a different ns-2 version, just create the appropriate patch and share it if you want.
UM-OLSR can be used like any other routing agent in ns-2, so you can use the node-config command to attach an OLSR routing agent to the mobile nodes which are to be created.
$ns_ node-config -adhocRouting OLSR
After creating your mobile nodes, you can configure each UM-OLSR routing agent individually or all at once. But first we will see the available configuration options and their default value.
- debug_ : Print debugging messages on stdout (false).
- use_mac_ : Enable link-layer feedback (false).
- willingness_ : Set the willingness for forwarding data packets on behalf of other nodes (WILL_DEFAULT = 3).
- hello_ival_ : Set the interval of HELLO messages transmission (2 sec).
- tc_ival_ : Set the interval of TC messages transmission (5 sec).
- mid_ival_ : Set the interval of MID messages transmission (5 sec). This has no actual effect in the simulation, since multiple interfaces are not supported.
In oder to configure all agents, write sentences like these:
Agent/OLSR set debug_ true Agent/OLSR set hello_ival_ 3
In order to configure a single agent:
set ra [$mobilenode agent 255] $ra set use_mac_ true $ra set tc_ival_ 6
By default, every UM-OLSR packet may piggyback up to 4 OLSR messages. You can change this value by redefining the OLSR_MAX_MSGS constant and recompiling the simulator. For the simulation results, the length of IPv4 addresses are assumed by default. If you prefer the length of IPv6 addresses, define OLSR_IPv6 and compile again.
Once you have performed a simulation, you get a trace file where you can see what happened during the execution. Let us see with some examples the format of the traces generated by UM-OLSR. Following examples use the classic notation of ns-2 trace files. However, “tagged” and “new trace” formats are also supported.
s 21.537326976 _0_ RTR --- 98 OLSR 56 [0 0 0 0] ------- [0:255 -1:255 32 0] [1 12 [HELLO 0 0 12]]
The line above indicates that node 0 is sending an OLSR packet (size = 56 bytes) which contains one HELLO message. Specific information about the OLSR packet is by the end of the line (inside the final brackets): number of contained messages, packet sequence number, and the list of OLSR messages. Then we find information about the messages themselves: type, originator address, hop count and message sequence number.
r 13.833447485 _2_ RTR --- 45 OLSR 84 [0 ffffffff 1 800] ------- [1:255 -1:255 32 0] [2 10 [HELLO 1 0 10][TC 1 0 11]]
The example above shows the reception of a packet which piggybacks two messages, one HELLO and one TC. Information about each one is also shown. If you need further details about the ns-2 trace formats, please see the ns-2 manual.
This is a one-person project and I am the only author of the code. It was developed as part of my work toward the B.Sc. degree in the University of Murcia. In fact, this was my first public software release.